Plumbing Basics: Before Installing a Bathtub
Plumbing Basics: Before Installing a Bathtub
Blog Article
What are your opinions with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't exactly rocket science, but it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably hard project. If the old tub is conveniently accessible, the project can move easily; if you need to open up a wall surface to eliminate the old tub as well as position the new bath tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to leave the old tub and set in the brand-new one. See to it you have actually certified on your own for the job as well as fit attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is much better to consider using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you install a new tub in your bathroom if you have currently acquired a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your devices and also product checklist should comprise the following:
Preparing for the Installment
To start with, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome as a result of the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will originate from the pipes. When the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
Before moving on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the called for setting. The wood boards are useful in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the level as well as readjusting the feet on the bath tub up until the spirit level reads degree.
To mount taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub should wait up until the bath tub has been utilized at the very least once as this will certainly settle it right into its final position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making certain that the washing machines remain in place between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealer can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our part on Tools You Need to Install a New Bathtub . Many thanks for taking time to read our article post. Are you aware of somebody who is interested in the niche? Be sure promote it. Thanks for your time. Kindly pay a visit to our website back soon.
Diverse plumbing issues? We resolve. Report this page